The car oil spill happens frequently, many friends around have mentioned this matter, some do not know how to deal with the situation and do not want to repair the factory but ignore it. In fact, the occurrence of each situation is the car has more or less problems, this can not be careless, the oil spill may affect the technical performance of the car, causing smooth oil, fuel waste, and so on, and even leave a hidden danger of accidents. So what happened to the oil spill? The following editors will teach you how to prevent the correct attitude of the car oil spill immediately! 

　　汽車漏油如何預防？

　　How to prevent car oil leakage?

　　1、輪轂軸承采用適量光滑，經常疏浚和清洗后橋殼上的通氣孔與螺塞，確保其與大氣連通。頻繁制動時為避免輪轂發熱，油脂變稀，可向輪轂灑水降溫或裝置淋水安裝。

　　1. Hub bearings are smooth in proper amount, often dredged and cleaned after the axle housing ventilation holes and plugs, to ensure its connection with the atmosphere. When braking frequently, in order to avoid the heat of the hub and the thinning of the grease, water can be sprayed on the hub to cool down or the device can be installed with water sprinkler.

　　2、定期改換損壞失效的油封、密封墊圈。假如仍不能消弭漏油，應拉出減震器，若感到有發卡或輕重不一時，再進一步檢查活塞與缸筒間的間隙能否過大，減震器活塞連桿有無彎曲等。

　　2. Regular replacement of damaged and invalid oil seals and sealing gaskets. If the oil leakage can not be eliminated, the shock absorber should be pulled out. If you feel that there are hairpins or different weights, then further check whether the gap between the piston and cylinder is too large, whether the piston connecting rod of the shock absorber is bent, etc.

　　3、車上各類緊固螺母按規則擰緊。零件運用過久會產生磨損過限(如活塞與汽缸等)，應及早檢修或改換磨損件。

　　3. All kinds of fastening nuts on the car should be tightened according to the rules. If the parts are used too long, the wear limit (such as piston and cylinder) will occur. The wear parts should be repaired or replaced as early as possible.

　　4、防止單向閥、通氣閥堵死，需對車輛停止定期檢查、疏浚、清洗。

　　4. To prevent blockage of one-way valves and ventilation valves, regular inspection, dredging and cleaning of vehicles should be stopped.

　　普通哪些更容易呈現漏油！

　　Ordinary which centers are more likely to show oil spills! __________

　　一、發起機油底殼：由于墊片老化或損壞、螺絲松動招致的漏油。（倡議：改換墊片或油底殼）

　　1. Initiating Oil Sump: Oil Leakage Caused by Gasket Aging or Damage and Screw Loosening. (Initiative: Replacement of gaskets or oil pans)

　　二、變速箱：運用條件苛刻、油封老化、箱體接合面損傷形成漏油。（倡議：改換變速箱密封墊等停止維修）

　　2. Gearbox: the use of harsh conditions, aging oil seals, damage to the joint surface of the box body to form oil leakage. (Initiative: Change gearbox gasket, etc. Stop maintenance)

　　三、氣門室蓋：襯墊的密封性不嚴而呈現的漏油。（倡議：改換密封墊）

　　3. Valve compartment cover: Oil leakage due to improper sealing of gaskets. (Initiative: Replacement of gaskets)

　　四、機油散熱器：密封墊老化密封不嚴呈現的漏油。（倡議：改換密封墊）

　　4. Oil Radiator: Oil leakage due to ageing of sealing gasket and improper sealing. (Initiative: Replacement of gaskets)

　　五、曲軸：由于前油封和后油封因老化呈現漏油，其中前油封漏油較常見。（倡議：改換前后油封）

　　Fifth, crankshaft: Because the front oil seal and the rear oil seal are leaking due to aging, the front oil seal is more common. (Initiative: oil seals before and after replacement)

　　六、球籠:長期的磨損決裂都會招致呈現漏油。（倡議：改換防塵套或球籠）

　　6. Ball cage: Long-term wear and tear will lead to oil leakage. (Initiative: Replacement of dustproof sleeve or ball cage)